skip to main content

Enhancing microbial fuel cell performance with carbon powder electrode modifications for low-power sensors modules

1Centre for Sustainable Communication and Internet of Things (CSCIoT), Faculty of Engineering and Technology, Multimedia University, Melaka, Malaysia

2Department for Computer Engineering and Computer Science (CECS), School of Engineering and Computing (SOEC), MILA University, Nilai, Negeri Sembilan, Malaysia

3Faculty of Electrical Engineering, Universiti Malaya, Kuala Lumpur, Malaysia

Received: 8 Sep 2023; Revised: 10 Nov 2023; Accepted: 22 Nov 2023; Available online: 27 Nov 2023; Published: 1 Jan 2024.
Editor(s): H. Hadiyanto
Open Access Copyright (c) 2024 The Author(s). Published by Centre of Biomass and Renewable Energy (CBIORE)
Creative Commons License This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Citation Format:

Microbial Fuel Cell (MFC) is a promising technology for harnessing energy from organic compounds. However, the low power generation of MFCs remains a significant challenge that hinders their commercial viability. In this study, we reported three distinct modifications to the stainless-steel mesh (SSM), carbon cloth, and carbon felt electrodes using carbon powder (CP), a mixture of CP and ferrum, and a blend of CP with sodium citrate and ethanol. The MFC equipped with an SSM and CP anode showed a notable power density of 1046.89 mW.m-2. In comparison, the bare SSM anode achieved a maximum power density of 145.8 mW m-2. Remarkably, the 3D-modified SSM with a CP anode (3D-SSM-CP) MFC exhibited a substantial breakthrough, attaining a maximum power density of 1417.07 mW m-2. This achievement signifies a significant advancement over the performance of the unaltered SSM anode, underscoring the effectiveness of our modification approach. Subsequently, the 3D-SSM-CP electrode was integrated into single-chamber MFCs, which were used to power a LoRaWAN IoT device through a power management system. The modification methods improved the MFC performance while involving low-cost and easy fabricating techniques. The results of this study are expected to contribute to improving MFC's performance, bringing them closer to becoming a practical source of renewable energy.

Fulltext View|Download
Keywords: Anode Modification; Carbon Powder; Internet of Things (IoT); Microbial Fuel Cell; Power Management Systems; Renewable Energy; Stainless-Steel Mesh.

Article Metrics:

  1. Bose, D., Bose, A., Kundani, D., Gupta, D., Jain, H. (2018). Comparative analysis of carbon cloth and aluminum electrodes using agar salt-bridge based microbial fuel cell for bioelectricity generation from effluent derived wastewater. Nature Environment and Pollution Technology, 17(4), 1201–1205.
  2. Chen, X., Li, Y., Yuan, X., Li, N., He, W., & Liu, J. (2020). Synergistic effect between poly(diallyldimethylammonium chloride) and reduced graphene oxide for high electrochemically active biofilm in microbial fuel cell. Electrochimica Acta, 359, 136949.
  3. Chong, P. L., Singh, A. K., & Kok, S. L. (2019a). Potential application of Aloe Vera-derived plant-based cell in powering wireless device for remote sensor activation. PLOS ONE, 14(12), e0227153.
  4. Chong, P. L., Singh, A. K., & Kok, S. L. (2019b). Characterization of Aloe Barbadensis Miller leaves as a potential electrical energy source with optimum experimental setup conditions. PLOS ONE, 14(6), e0218758.
  5. Chong, P. L., Singh, A. K., & Kong, F. Y. (2022). Renewable energy from living plants to power IoT sensor for remote sensing. Journal of Engineering Technology. 11(1) ,
  6. Duarte, K. D., & Kwon, Y. (2020). In situ carbon felt anode modification via codeveloping Saccharomyces cerevisiae living-template titanium dioxide nanoclusters in a yeast-based microbial fuel cell. Journal of Power Sources, 474, 228651.
  7. Ewing, T., Babauta, J. T., Atci, E., Tang, N., Orellana, J., Heo, D., & Beyenal, H. (2014). Self-powered wastewater treatment for the enhanced operation of a facultative lagoon. Journal of Power Sources, 269, 284–292.
  8. Gajda, I., Greenman, J., Melhuish, C., & Ieropoulos, I. (2015). Simultaneous electricity generation and microbially-assisted electrosynthesis in ceramic MFCs. Bioelectrochemistry, 104, 58–64.
  9. Geetanjali, Rani, R., & Kumar, S. (2019a). Enhanced Performance of a Single Chamber Microbial Fuel Cell Using NiWO4/Reduced Graphene Oxide Coated Carbon Cloth Anode. Fuel Cells, 19(3), 299–308.
  10. Geetanjali, Rani, R., & Kumar, S. (2019b). High-capacity polyaniline-coated molybdenum oxide composite as an effective catalyst for enhancing the electrochemical performance of the microbial fuel cell. International Journal of Hydrogen Energy, 44(31), 16933–16943.
  11. Guan, Y. F., Zhang, F., Huang, B. C., & Yu, H. Q. (2019). Enhancing electricity generation of microbial fuel cell for wastewater treatment using nitrogen-doped carbon dots-supported carbon paper anode. Journal of Cleaner Production, 229, 412–419.
  12. Guo, K., Donose, B. C., Soeriyadi, A. H., Prévoteau, A., Patil, S. A., Freguia, S., Gooding, J. J., & Rabaey, K. (2014). Flame Oxidation of Stainless Steel Felt Enhances Anodic Biofilm Formation and Current Output in Bioelectrochemical Systems. Environmental Science & Technology, 48(12), 7151–7156.
  13. Ieropoulos, I. A., Stinchcombe, A., Gajda, I., Forbes, S., Merino-Jimenez, I., Pasternak, G., Sanchez-Herranz, D., & Greenman, J. (2016). Pee power urinal – microbial fuel cell technology field trials in the context of sanitation. Environmental Science: Water Research & Technology, 2(2), 336–343.
  14. Jia, X., He, Z., Zhang, X., & Tian, X. (2016). Carbon paper electrode modified with TiO2 nanowires enhancement bioelectricity generation in microbial fuel cell. Synthetic Metals, 215, 170–175.
  15. Khaled, F., Ondel, O., & Allard, B. (2016). Microbial fuel cells as power supply of a low-power temperature sensor. Journal of Power Sources, 306, 354–360.
  16. Li, H., Liao, B., Xiong, J., Zhou, X., Zhi, H., Liu, X., Li, X., & Li, W. (2018b). Power output of microbial fuel cell emphasizing interaction of anodic binder with bacteria. Journal of Power Sources, 379, 115–122.
  17. Li, M., Zhou, M., Tian, X., Tan, C., McDaniel, C. T., Hassett, D. J., & Gu, T. (2018a). Microbial fuel cell (MFC) power performance improvement through enhanced microbial electrogenicity. Biotechnology Advances, 36(4), 1316–1327.
  18. Li, S., Cheng, C., & Thomas, A. (2016). Carbon‐Based Microbial‐Fuel‐Cell Electrodes: From Conductive Supports to Active Catalysts. Advanced Materials, 29(8).
  19. Liang, Y., Feng, H., Shen, D., Li, N., Guo, K., Zhou, Y., Xu, J., Chen, W., Jia, Y., & Huang, B. (2017). Enhancement of anodic biofilm formation and current output in microbial fuel cells by composite modification of stainless steel electrodes. Journal of Power Sources, 342, 98–104.
  20. Liu, Y. C., Hung, Y. H., Sutarsis, Hsu, C. C., Ni, C. S., Liu, T. Y., Chang, J. K., & Chen, H. Y. (2021). Effects of surface functional groups of coal-tar-pitch-derived nanoporous carbon anodes on microbial fuel cell performance. Renewable Energy, 171, 87–94.
  21. Malinis, M. P. D., Velasco, H. J. F., & Pamintuan, K. R. (2023). Performance evaluation of the novel 3D-printed aquatic plant-microbial fuel cell assembly with Eichhornia crassipes rnia crassipes. International Journal of Renewable Energy Development, 12(5), 942-951,
  22. Mohamed, H. O., Sayed, E. T., Obaid, M., Choi, Y. J., Park, S. G., Al-Qaradawi, S., & Chae, K. J. (2018). Transition metal nanoparticles doped carbon paper as a cost-effective anode in a microbial fuel cell powered by pure and mixed biocatalyst cultures. International Journal of Hydrogen Energy, 43(46), 21560–21571.
  23. Oliveira, V., Simões, M., Melo, L., & Pinto, A. (2013). Overview on the developments of microbial fuel cells. Biochemical Engineering Journal, 73, 53–64.
  24. Palmero, D. P. E., & Pamintuan, K. R. S. (2023). Characterization of plant growth promoting potential of 3D-printed plant microbial fuel cells. International Journal of Renewable Energy Development, 12(5), 842–852.
  25. Prasad, J., & Tripathi, R. K. (2018). Scale up sediment microbial fuel cell for powering Led lighting. International Journal of Renewable Energy Development, 7(1), 53.
  26. Pu, K. B., Ma, Q., Cai, W. F., Chen, Q. Y., Wang, Y. H., & Li, F. J. (2018). Polypyrrole modified stainless steel as high performance anode of microbial fuel cell. Biochemical Engineering Journal, 132, 255–261.
  27. Qiao, Y., Li, C. M., Bao, S. J., & Bao, Q. L. (2007). Carbon nanotube/polyaniline composite as anode material for microbial fuel cells. Journal of Power Sources, 170(1), 79–84.
  28. Wang, Y., Wen, Q., Chen, Y., & Qi, L. (2017). A novel polyaniline interlayer manganese dioxide composite anode for high-performance microbial fuel cell. Journal of the Taiwan Institute of Chemical Engineers, 75, 112–118.
  29. Yang, G., & Wang, J. (2019). Enhancing biohydrogen production from waste activated sludge disintegrated by sodium citrate. Fuel, 258, 116177.
  30. Yang, L., Wang, A., Wen, Q., & Chen, Y. (2021). Modified cobalt-manganese oxide-coated carbon felt anodes: an available method to improve the performance of microbial fuel cells. Bioprocess and Biosystems Engineering, 44(12), 2615–2625.
  31. Ying, X., Shen, D., Wang, M., Feng, H., Gu, Y., & Chen, W. (2018). Titanium dioxide thin film-modified stainless steel mesh for enhanced current-generation in microbial fuel cells. Chemical Engineering Journal, 333, 260–267.
  32. You, S. J., Wang, X. H., Zhang, J. N., Wang, J. Y., Ren, N. Q., & Gong, X. B. (2011). Fabrication of stainless steel mesh gas diffusion electrode for power generation in microbial fuel cell. Biosensors and Bioelectronics, 26(5), 2142–2146.
  33. Zhang, Y., Sun, J., Hu, Y., Li, S., & Xu, Q. (2013). Carbon nanotube-coated stainless steel mesh for enhanced oxygen reduction in biocathode microbial fuel cells. Journal of Power Sources, 239, 169–174.
  34. Zheng, S., Yang, F., Chen, S., Liu, L., Xiong, Q., Yu, T., Zhao, F., Schröder, U., & Hou, H. (2015). Binder-free carbon black/stainless steel mesh composite electrode for high-performance anode in microbial fuel cells. Journal of Power Sources, 284, 252–257.
  35. Zhong, D., Liu, Y., Liao, X., Zhong, N., & Xu, Y. (2018). Facile preparation of binder-free NiO/MnO2-carbon felt anode to enhance electricity generation and dye wastewater degradation performances of microbial fuel cell. International Journal of Hydrogen Energy, 43(51), 23014–23026.
  36. Zhou, S., Lin, M., Zhuang, Z., Liu, P., & Chen, Z. (2019). Biosynthetic graphene enhanced extracellular electron transfer for high performance anode in microbial fuel cell. Chemosphere, 232, 396–402.

Last update:

No citation recorded.

Last update: 2024-03-01 21:05:12

No citation recorded.