skip to main content

Toward eco-friendly dye-sensitized solar cells: Developing chitosan-based electrolytes with conducting polymers and ionic liquids

Department of Chemistry, Faculty of Mathematics and Natural Sciences, Universitas Gadjah Mada, Yogyakarta, 55281, Indonesia

Received: 28 Jan 2025; Revised: 6 Apr 2025; Accepted: 7 May 2025; Available online: 20 May 2025; Published: 1 Jul 2025.
Editor(s): Soulayman Soulayman
Open Access Copyright (c) 2025 The Author(s). Published by Centre of Biomass and Renewable Energy (CBIORE)
Creative Commons License This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Citation Format:
Abstract
Optimization of chitosan-based gel electrolytes modified with conducting polymers and ionic liquids for dye-sensitized solar cells (DSSC) has been done to improve its electrochemical activity. The effects of iodide salts, 1-propyl-3-methylimidazolium iodide (PMII), and polyaniline incorporation on the electrochemical properties of chitosan-based electrolyte, as well as its performance as a quasi-solid electrolyte in DSSC, were systematically investigated. A study on the effect of different iodide salts on the electrochemical properties of the electrolyte was conducted by employing various iodide salts (lithium iodide, sodium iodide, potassium iodide, or cesium iodide). Electrolytes with various amounts of PMII and polyaniline were also prepared. X-ray diffraction (XRD) and Fourier transform-infrared (FTIR) analysis were conducted to study the effect of iodide salts, PMII, and polyaniline on the change in intermolecular interaction of the chitosan matrix. The ionic conductivity and the redox activity of the chitosan-based electrolyte were respectively evaluated using conductometry and cyclic voltammetry analysis. It is found that the larger cation size of the iodide salts and a higher amount of PMII resulted in both higher intensity of the redox peak current and conductivity of the electrolyte. Those two characteristics increase with the presence of polyaniline, but the low transparency of this polyaniline-based electrolyte lowers the solar cell’s efficiency. The highest performance DSSC utilizing a chitosan/KI-PMII based electrolyte resulted in a Voc of 0.402 V, Jsc of 0.335 mA/cm², fill factor (FF) of 0.432, and an overall power conversion efficiency (PCE) of 0.058%. This efficiency is approximately one-third that of the conventional liquid electrolyte-based DSSC. The optimized chitosan-based electrolyte offers promising performance in replacing the low-stability liquid electrolyte-based DSSC.
Fulltext View|Download
Keywords: DSSC; chitosan; electrolyte; polyaniline; ionic liquid
Funding: Universitas Gadjah Mada under contract 7725/UN1.P.II/Dit-Lit/PT.01.03/2023

Article Metrics:

  1. Adel, R., Abdallah ,T., and Talaat, H. (2019). Efficiency enhancement of photovoltaic performance of dye sensitized solar cell using conducting polymer electrolyte of different functional group. Journal of Physics: Conference Series, 1253 (1), 012029. https://doi.org/10.1088/1742-6596/1253/1/012029
  2. Arof, A.K., Aziz, M.F., Noor, M.M., Careem, M.A., Bandara, L.R.A.K., Thotawatthage, C.A., Rupasinghe, W.N.S., and Dissanayake, M.A.K.L. (2014). Efficiency enhancement by mixed cation effect in dye-sensistized solar cells with a PVdF based gel polymer electrolyte. International Journal of Hydrogen Energy, 39, 2929 – 2935. https://doi.org/10.1016/j.ijhydene.2013.07.028
  3. Bandara, T.M.W.J., DeSilva, L.A.A., Ratnasekera, J.L., Hettiarachchi, K.H., Wijerathna, A.P., Thakurdesai, M., Preston, J., Albinsson, I., and Mellander, B.E. (2019). High Efficiency Dye-Sensitized Solar Cell Based on a Novel Gel Polymer Electrolyte Containing RbI and Tetrahexylammonium Iodide (Hex4NI) Salts and Multi-Layered Photoelectrodes of TiO2 Nanoparticles. Renewable Sustainable Energy Rev. 103, 282-290. https://doi.org/10.1016/j.rser.2018.12.052
  4. Bhattacharya, B., Lee, J.Y., Geng, J., Jung, H.T., and Park, J.K. (2009). Effect of cation size on solid polymer electrolyte based dye-sensitized solar cells. Langmuir, 25, 3276-3281. https://doi.org/10.1021/la8029177
  5. Buraidah, M.H., Teo, L.P., Au Yong, C.M., Shah, S., and Arof, A.K. (2016) Performance of polymer electrolyte based on chitosan blended with poly(ethylene oxide) for plasmonic dye-sensitized solar cell. Optical Materials, 57, 202-211. https://doi.org/10.1016/j.optmat.2016.04.028
  6. Buraidah, M.H., Teo, L.P., Majid, S.R., and Arof, A.K. (2010). Characteristics of TiO2/solid electrolyte junction solar cells with I/I3- redox couple. Optical Materials, 32, 723 – 728. https://doi.org/10.1016/j.optmat.2009.08.014
  7. Dissanayake, M.A.K.L., Jayathissa, R., Seneviratne, V.A., Thotawatthage, C.A., Senadeera, G.K.R., and Mellander, B.E. (2014). Polymethylmethacrylate (PMMA) based quasi-solid state electrolyte with binary iodide salt for efficiency enhancement in TiO2 based dye sensitized solar cells. Solid State Ionics, 265, 85-91. https://doi.org/10.1016/j.ssi.2014.07.019
  8. Gossen, K., Dotter, M., Brockhagen, B., Storck, J.L., and Ehrmann, A. (2022). Long-term investigation of unsealed DSSCs with glycerol-based electrolytes of different compositions. AIMS Materials Science, 9 (2), 283-296. https://doi.org/10.3934/matersci.2022017
  9. Green, M.A., Hishikawa, Y., Warta, W., Dunlop, E.D., Levi, D.H., Hohl-Ebinger, J., and Ho-Baillie, A.W.H. (2017). Solar Cell Efficiency Tables (Version 50). Prog. Photovoltaics, 25, 668-676. https://doi.org/10.1002/pip.2909
  10. Gupta R.K., and Rhee H.-W. (2013). Plasticizing effect of K+ ions and succinonitrile on electrical conductivity of [poly(ethylene oxide)-succinonitrile]/KI-I2 redox-couple solid polymer electrolyte. Journal of Physical Chemistry B, 117 (24), 7465 - 7471. https://doi.org/10.1021/jp4025798
  11. Hidayat, A., Solikah, S., Shafa, A.V.A., and Hatmanto, A.D. (2024). Hypothetical introduction of TiO2 nanodecahedrons (TN(10)) as the design for quasi solid dye sensitized solar cells based on KI-I2/chitosan/PAni-chitosan/TN(10) by the p-n junction theory. Electrochimica Acta, 477, 143740. https://doi.org/10.1016/j.electacta.2023.143740
  12. Huang, Y.-J., Sahoo, P.K., Tsai, D.-S., and Lee, C.-P. (2021). Recent advances on pt-free electro-catalysts for dye-sensitized solar cells. Molecules, 26 (17), 5186. https://doi.org/10.3390/molecules26175186
  13. Jolly, D., Pelleja, L., Narbey, S., Oswald, F., Chiron, J., Clifford, J., Palomares, E., and Demadrille, R. (2014). Robust organic dye for dye sensitized solar cells based on iodine/iodide electrolytes combining high efficiency and outstanding stability. Scientific Reports, 4 (4033), 1-7. https://doi.org/10.1038/srep04033
  14. Kaneto, K., Hata, F., Uto, S. (2018). Structure and size of ions electrochemically doped in conducting polymer. Journal of Micromechanics and Microengineering, 28 (5), 054003. https://doi.org/10.1088/1361-6439/aaaef5
  15. Karlybaeva, B.P., Berdimbetova, G.E., Boymirzaev, A.S. (2023). Synthesis and characteristics of sulfated chitosan based on chitin/chitosan from artemia parthenogenetica cysts. Chemical Problems, 3 (21), 242-250. https://doi.org/10.32737/2221-8688-2023-3-242-250
  16. Ki S., Park A., Lee W.B., Kim, Y.J., and Chang J. (2023). Overlimiting current by iodide electrode oxidation in aqueous media: an electrogenerated iodine interphase with positively charged channels stimulating in situ electrokinetic iodide transport. Journal of Materials Chemistry A, 11 (26), 14366-14379. https://doi.org/10.1039/D3TA01505J
  17. Kim, S.G., Ju, M.J., Choi, I.T., Choi, W.S., Choi, H.J., Baek, J.B., and Kim, H.K. (2013). Nb-doped TiO2 nanoparticles for organic dye-sensitized solar cells. RSC Advances, 3 (37), 16380 - 16386. https://doi.org/10.1039/C3RA42081G
  18. Kitazawa, Y., Iwata, K., Kido, R., Imaizumi, S., Tsuzuki, S., Shinoda, W., Ueno, K., Mandai, T., Kokubo, H., Dokko, K., and Watanabe, M. (2018). Polymer Electrolytes Containing Solvate Ionic Liquids: A New Approach to Achieve High Ionic Conductivity, Thermal Stability, and a Wide Potential Window. Chem. Mater. 30, 252-261. https://doi.org/10.1021/acs.chemmater.7b04274
  19. Kusumawati, N., Setiarso, P., Muslim, S., Hafidha, Q.A., Cahyani, S.A., and Fachrirakarsie, F.F. (2024). Optimization Thickness of Photoanode Layer and Membrane as Electrolyte Trapping Medium for Improvement Dye-Sensitized Solar Cell Performance. Science and Technology Indonesia, 9 (1), 7-16. https://doi.org/10.26554/sti.2024.9.1.7-16
  20. Lai Y.-L., Hsu H.-R., Lai Y.-K., Zheng, C.-Y, Chou, Y.-H., Hsu, N.-K., and Lung G.-Y. (2017). Influence of thin film thickness of working electrodes on photovoltaic characteristics of dye-sensitized solar cells. MATEC Web of Conferences, 123, 00030. https://doi.org/10.1051/matecconf/201712300030
  21. Lemos, H.G., Barba, D., Selopal, G.S., Wang, C., Wang, Z.M., Duong, A., Rosei, F., Santos, S.F., and Venancio, E.C. (2020). Water-dispersible polyaniline/graphene oxide counter electrodes for dye-sensitized solar cells: Influence of synthesis route on the device performance. Sol. Energy, 207, 1202-1213. https://doi.org/10.1016/j.solener.2020.07.021
  22. Li, G.B., Wang, J., Kong, X.P. (2020). Coprecipitation-based synchronous pesticide encapsulation with chitosan for controlled spinosad release. Carbohydr. Polym., 249, 116865. https://doi.org/10.1016/j.carbpol.2020.116865
  23. Lichawska, M.E., Kufelnicki A., Wozniczka, M. (2019). Interaction of microcrystalline chitosan with graphene oxide (GO) and magnesium ions in aqueous solution. BMC Chemistry, 13 (3), 57. https://doi.org/10.1186/s13065-019-0574-y
  24. Liu, G., Hu, M., Du, X., Qi, B., Lu, K., Zhou, S., Xie, F., and Li, Y. (2022). Study on the interaction between succinylated soy protein isolate and chitosan and its utilization in the development of oil-in-water bilayer emulsions. Food Hydrocoll., 124, 107309. https://doi.org/10.1016/j.foodhyd.2021.107309
  25. Lozkins, S., Hodakovska, J., Kleperis, J., and Merijs-Meri, R. (2019). Nafion® and polyaniline composite modification with Li and Mg ions. IOP Conference Series: Materials Science and Engineering, 503 (1), 012031. https://doi.org/10.1088/1757-899X/503/1/012031
  26. Mahmood, H., Shakeel, A., Rafique, S., and Moniruzzaman, M. (2022). Recent progress in ionic liquid-assisted processing and extraction of biopolymers. Biocatalysis in Green Solvents, 233-255. https://doi.org/10.1016/B978-0-323-91306-5.00015-7
  27. Manikandan, K.M., Yelilarasi, A., Senthamaraikannan, P., Saravanakumar, S.S., Khan, A., and Asiri, A.M. (2018). The conducting polymer electrolyte based on polypyrrole-polyvinyl alcohol and its application in low-cost quasi-solid-state dye-sensitized solar cells. J. Solid State Electr., 22, 3785-3797. https://doi.org/10.1007/s10008-018-4070-4
  28. O’Regan, B., and Gratzel, M. (1991). A low-cost, high-efficiency solar cell based on dye-sensitized colloidal TiO2 films. Nature, 353 (6346), 737-740. http://dx.doi.org/10.1038/353737a0
  29. Polesca, C., Passos, H., Coutinho, J.A.P., and Freire, M.G. (2022). Sustainable development of biomaterials using ionic liquids. Current Opinion in Green and Sustainable Chemistry, 37, 100675. https://doi.org/10.1016/j.cogsc.2022.100675
  30. Prabakaran, K., Mohanty, S., and Nayak, S.K. (2015). Improved electrochemical and photovoltaic performance of dye sensitized solar cells based on PEO/PVdF-HFP/silane modified TiO2 electrolytes and MWNCT/Nafion counter electrode. RSC Advances, 5, 40491-40504. https://doi.org/10.1039/C5RA01770J
  31. Pullanjiot, N., and Swaminathan, S. (2019). Enhanced electrochemical properties of metal oxide interspersed polymer gel electrolyte for QSDSSC application. Sol. Energy, 186, 37–45. https://doi.org/10.1016/j.solener.2019.04.086
  32. Senevirathne, A.M.C., Seneviratne, V.A., Ileperuma, O.A., Bandara, H.M.N., and Rajapakse, R.M.G. (2016). Novel Quasi-Solid-State Electrolyte Based on γ-Butyrolactone and Tetrapropylammonium Iodide for Dye-Sensitized Solar Cells Using Fumed Silica as the Gelling Agent. Procedia Engineering, 139, 87-92. https://doi.org/10.1016/j.proeng.2015.08.1117
  33. Shafiee, A., Salleh, M.M., and Yahaya, M. (2011). Determination of HOMO and LUMO of [6,6]-phenyl C61-butyric acid 3-ethylthiophene ester and poly(3-octyl-thiophene-3,5-diyl) through voltammetry characterization. Sains Malaysiana, 40(2), 173-176
  34. Singh, P.K., Bhattacharya, B., Nagarale, R.K., Kim, K.W., and Rhee, H.W. (2010). Synthesis, characterization and application of biopolymer-ionic liquid composite membranes. Synthetic Metals, 160, 139 – 142. https://doi.org/10.1016/j.synthmet.2009.10.021
  35. Solikah, S., Hidayat, A., Suyanta, S., and Hatmanto, A.D. (2024). Crystalline phase dependence of the electrochemical properties of chitosan/polyaniline/TiO2-KI/I2 quasi solid polymer electrolyte. Materials Science and Engineering B, 307, 117531. https://doi.org/10.1016/j.mseb.2024.117531
  36. Soud, S.A., Ali, M.A., Alhadban, W.G., and Taha, A.A. (2024). Extraction and characterization of chitin and chitosan from local Iraqi fish scales. Iraqi Journal of Agricultural Sciences, 55 (5), 1728-1733. https://doi.org/10.36103/1zah0b15
  37. Tamilselvan, S.N., Shanmugan, S., (2024). Towards sustainable solar cells: unveiling the latest developments in bio-nano materials for enhanced DSSC efficiency. Clean Energy. 8 (3), 238-257. https://doi.org/10.1093/ce/zkae031
  38. Tang, Z.,Wu, J., Liu, Q., Zheng, M., Tang, Q., Lan, Z., and Lin, J. (2012). Preparation of poly(acrylic acid)/gelatin/polyaniline gel-electrolyte and its application in quasi-sloid state dye sensitized solar cells. Journal of Power Sources, 203, 282-287. https://doi.org/10.1016/j.jpowsour.2011.11.039
  39. Theerthagiri, J., Senthil, R.A., Buraidah, M.H., Madhavan, J., Arof, A.K., and Ashokkumar, M. (2016). One-step Electrochemical Deposition of Ni1–xMoxS Ternary Sulfides as an Efficient Counter Electrode for Dye-sensitized Solar Cells. J. Mater. Chem., 4, 16119-16127. https://doi.org/10.1039/C6TA04405K
  40. Vimala, V., Cindrella, L. (2022). Binder-free polymer material embedded in chitosan matrix for electrochemical energy storage devices. Chemical Physics Letters, 809, 140172. https://doi.org/10.1016/j.cplett.2022.140172
  41. Wang, X., Kulkarni, S.A., Ito, B.I., Batabyal S.K., Nonomura, K., Wong, C.C., Gratzel, M., Mhaisalkar, S.G., and Uchida, S. (2013). Nanoclay Gelation Approach toward Improved Dye-Sensitized Solar Cell Efficiencies: An Investigation of Charge Transport and Shift in the TiO2 Conduction Band. ACS Applied Materials & Interfaces, 5 (2), 444-450. https://doi.org/10.1021/am3025454
  42. Wu, T.Y., Tsao, M.H., Chen, F.L., Su, S.G., Chang, C.W., Wang, H.P., Lin, Y.C., and Sun, I.W. (2010). Synthesis and characterization of three organic dyes with various donors and rhodamine ring acceptor for using in dye-sensitized solar cells. Journal of The Iranian Chemical Society, 7(3), 707-720. https://doi.org/10.1007/BF03246061
  43. Yahya, W.Z.N., Hong, P.Z., Zain, W.Z.Z.W.M., and Mohamed, N.M. (2020). Tripropyl Chitosan iodide-based gel polymer electrolyte as quasi solid-state dye sensitized solar cells. Materials Science Forum, 997, 69-76. https://doi.org/10.4028/www.scientific.net/MSF.997.69
  44. Yahya, W.Z.N., Meng, W.T., Khatani, M., Samsudin, A.E., and Mohamed, N.M. (2017). Bio-based chitosan/PVdF-HFP polymer-blend for quasi-solid state electrolyte dye-sensitized solar cells. e-Polymers, 17(5), 355-361. https://doi.org/10.1515/epoly-2016-0305
  45. Zanotti, G., Angelini, N., Notarantonio, S., Paoletti, A.M., Pennesi, G., Rossi, G., Lembo, A., Colonna, D., Di Carlo, A., Reale, A., Brown, T.M., and Calogero G. (2010). Bridged Phthalocyanine Systems for Sensitization of Nanocrystalline TiO2 Films. International Journal of Photoenergy, 136807, 1-11. https://doi.org/10.1155/2010/136807
  46. Zhang, J., Yu, C., Wang, L., Li, Y., Ren, Y., and Shum, K. (2014). Energy barrier at the N719-dye/CsSnI3 interface for photogenerated holes in dye-sensitized solar cells. Scientific Reports, 4(6954), 1-6. https://doi.org/10.1038/srep06954
  47. Zhang, W., Tao, L., Wang, H., and Zhang, J. (2018). Research Progress on Quasi-Solid-State Electrolytes of Dye-Sensitized Solar Cells. Materials China. 37 (7), 543-550. https://doi.org/10.7502/j.issn.1674-3962.2018.07.07

Last update:

No citation recorded.

Last update: 2025-10-05 22:08:07

No citation recorded.