DOI: https://doi.org/10.61435/ijred.2026.61922
|  Research Instrument
Covering letter
Subject
Type Research Instrument
  Download (13KB)    Indexing metadata
 Research Instrument
Similarity report
Subject
Type Research Instrument
  Download (3MB)    Indexing metadata

The Effect of Temperature during the Hydrocracking of Low-Density Polyethylene Using a Ni-Cu/HZSM-5 Catalyst

1Chemistry Study Program, Universitas Negeri Semarang, Indonesia

2Department of Chemistry, Universitas Negeri Semarang, Indonesia

3Research Center for Catalysis, National Research and Innovation Agency, KST BJ Habibie Build. 452, Tangerang Selatan, Indonesia 15341., Indonesia

4 Research Center for Molecular Chemistry, National Research and Innovation Agency (BRIN), KST BJ Habibie Build. 452, Tangerang Selatan, Indonesia 15341., Indonesia

View all affiliations
Received: 30 Oct 2025; Published: 2 May 2026.
Editor(s): H Hadiyanto
Open Access Copyright (c) 2025 The Author(s). Published by Centre of Biomass and Renewable Energy (CBIORE)
Creative Commons License This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Citation Format:
Abstract
LDPE plastics contributed 20-30% of the plastics use. Due to its non-biodegradable properties, plastic waste management is crucial. In the other hand, the LDPE plastics provide potential and benefits in the exploration of energy resources; they could be converted to liquid fuels through a catalytic hydrocracking. This study focuses on the effect of temperatures during the hydrocracking of LDPE using a Ni-Cu/HZSM-5 catalyst. The Ni-Cu/HZSM-5 catalyst was synthesized using the wet impregnation method assisted by ultrasonic irradiation. The characteristics of the catalyst were evaluated prior to its use during the hydrocracking of LDPE. This study showed that the impregnation of Ni and Cu at HZSM-5 surface did not significantly affect the crystallinity of HZSM-5. Even though the peaks of Ni and Cu in the diffraction pattern were not clearly observed, their presence at HZSM-5 surface was well confirmed by the XRF spectrum. In addition, the hierarchical structure of HZSM-5 was also confirmed by the appearance of microporosity together with the type-IV hysteresis loop on the nitrogen adsorption-desorption isotherm. A considerable decrease (~25%) of the catalyst acidity was observed after the impregnation of Ni and Cu at HZSM-5 surface. The Ni-Cu/HZSM-5 catalyst showed a good activity during the hydrocracking of LDPE at temperatures of 275−400 °C, resulting in liquid, solid, and gas products. The yields of the liquid product increased by increasing the hydrocracking temperatures. It was observed that by increasing the hydrocracking temperatures, the yield of the kerosene and diesel fractions decreased, while the yield of the gasoline fraction increased, as supported by the density and calorific value that was close to the commercial gasoline. A further temperature increase would lead to more products with lighter fractions, reducing the yield of gasoline. This was also supported by the presence of alkenes, ketones, and esters formed after the catalytic hydrocracking as shown by the FTIR spectra of the liquid products.

Note: This article has supplementary file(s).

Keywords: LDPE plastics; catalytic hydrocracking; Ni-Cu/HZSM-5 catalyst

Article Metrics:

Article Info
Section: Original Research Article
Language : EN
Recent articles
Economic growth and renewable energy consumption in Asia: Does good governance mitigate the trade-off? Methodology for the Selection and Optimal Sizing of Standalone PV / Wind Energy Systems with Battery Storage under Resource Availability Constraints Experimental Investigation of a Wildlife-Safe Origami-Inspired Reaction-Type Wind Turbine for Sustainable Urban Energy Systems Development of Hybrid COA-WCA Multi-Objective Optimization of Microgrid Hybrid Renewable Energy System: A Case Study of Nusa Penida Economic Environmental Optimization in Multiple Renewable Energy Sources with Demand Response based on Multi-Objective Optimization Algorithm More recent articles
Most cited articles
A Review on Solar PV Based Grid Connected Microinverter Control Schemes and Topologies Tax Incentive Policy for Geothermal Development: A Comparative Analysis in ASEAN Sizing and Optimization for Hybrid Central in South Algeria Based on Three Different Generators Optimization of Lipid Extraction from Municipal Scum Sludge for Biodiesel Production Using Statistical Approach Optimization and Molecular Characterization of Syngas Fermenting Anaerobic Mixed Microbial Consortium TERI SA1 More cited articles
  1. Akça, B., Can, M., Değirmenci, V., Yilmaz, A., & Üner, D. (2007). Single step synthesis of mesoporous Co-Pb/SBA-15 catalysts (K. Eguchi, M. Machida, & I. Yamanaka (eds.); pp. 317–320). Studies in Surface Science and Catalysis; https://doi.org/https://doi.org/10.1016/B978-0-444-53202-2.50068-3
  2. Akhtar, M.N., Ahmad, N., & Alqudayri, F. (2025). Catalytic transformation of LDPE into aromatic-rich fuel oil. Catalysts, 15(6), 532. https://doi.org/10.3390/catal15060532
  3. Al Muttaqii, M., Marbun, M.P., Sudibyo, S., Aunillah, A., Pranowo, D., Hasanudin, H., Rinaldi, N., & Bardant, T.B. (2024). Conversion of sunan candlenut oil to aromatic hydrocarbons with hydrocracking process over nano-HZSM-5 Catalyst. Bulletin of Chemical Reaction Engineering and Catalysis, 19(1), 141–148. https://doi.org/10.9767/bcrec.20116
  4. Al-Muttaqii, M., Kurniawansyah, F., Prajitno, D.H., & Roesyadi, A. (2019). Hydrocracking of coconut oil over Ni-Fe/HZSM-5 catalyst to produce hydrocarbon biofuel. Indonesian Journal of Chemistry, 19(2), 319–327; https://doi.org/10.22146/ijc.33590
  5. Al-Salem, S. M., Antelava, A., Constantinou, A., Manos, G., & Dutta, A. (2017). A Review on Thermal and Catalytic Pyrolysis of Plastic Solid Waste (PSW). Journal of Environmental Management, 197(1408), 177–198; https://doi.org/10.1016/j.jenvman.2017.03.084
  6. Darmaningsih, A., Suwandi, & Fitriyanti, N. (2019). Uji kalor bahan bakar campuran solar dan minyak nabati. E-Proceeding of Engineering, 6(1), 1370–1376
  7. Daryoso, K., Wahyuni, S., & Saputro, H. (2012). Uji aktivitas katalis ni-mo/zeolit pada reaksi hidrorengkah fraksi sampah plastik (polietilen). 1(2252)
  8. Dewan Energi Nasional. (2023). Outlook Energi Indonesia 2023. In Dewan Energi Nasional (2023rd ed.). Dewan Energi Nasional. https://www.esdm.go.id/assets/media/content/content-outlook-energi-indonesia-2019-bahasa-indonesia.pdf
  9. Febriana, I., Ramadhini, T.K., & Aulia, T. (2020). Pengaruh temperatur dan waktu reaksi minyak jelantah dengan zeolit alam pada produksi biofuel. Jurnal Kinetika, 11(3), 53–59
  10. Genet, M.B., Sendekie, Z.B., & Jembere, A.L. (2021). Investigation and optimization of waste LDPE plastic as a modifier of asphalt mix for highway asphalt: case of Ethiopian roads. Case Studies in Chemical and Environmental Engineering, 4, 100150; https://doi.org/10.1016/j.cscee.2021.100150
  11. Gorzin, F., Towfighi Darian, J., Yaripour, F., & Mousavi, S.M. (2018). Preparation of hierarchical HZSM-5 zeolites with combined desilication with NaAlO2/tetrapropylammonium hydroxide and acid modification for converting methanol to propylene. RSC Advances, 8(72), 41131–41142; https://doi.org/10.1039/c8ra08624a
  12. Hariadi, D., Saleh, S.M., Anwar Yamin, R., & Aprilia, S. (2021). Utilization of LDPE plastic waste on the quality of pyrolysis oil as an asphalt solvent alternative. Thermal Science and Engineering Progress, 23, 100872; https://doi.org/10.1016/j.tsep.2021.100872
  13. Hauli, L., Wijaya, K., & Syoufian, A. (2020). Fuel production from LDPE-based plastic waste over chromium supported on sulfated zirconia. Indonesian Journal of Chemistry, 20(2), 422–429; https://doi.org/10.22146/ijc.45694
  14. Karim, T.M., Toyoda, H., Sawada, M., Zhao, L., Wang, Y., Xiao, P., Wang, L., Huang, J., & Yokoi, T. (2024). Aluminum distribution on the microporous and hierarchical ZSM-5 intracrystalline and its impact on the catalytic performance. Chem & Bio Engineering, 1(9), 805-816; https://doi.org/10.1021/cbe.4c00117
  15. Khromova, S.A., Smirnov, A.A., Bulavchenko, O.A., Saraev, A.A., Kaichev, V.V, Reshetnikov, S.I., & Yakovlev, V.A. (2014). Applied catalysis A : General anisole hydrodeoxygenation over Ni–Cu bimetallic catalysts: The effect of Ni/Cu ratio on selectivity. Applied Catalysis A: General, 470, 261–270. https://doi.org/10.1016/j.apcata.2013.10.046
  16. Lao, K., Liu, X., Lin, H., Wen, L., Pan, Y., Hu, T., Tao, H.B. & Zheng, N. (2025). Is high specific surface area essential for anode catalyst supports in proton exchange membrane water electrolysis? Materials Horizons, 12(21), 9069-9078; https://doi.org/10.1039/D5MH01127B
  17. Li, L., Zuo, J., Duan, X., Wang, S., & Chang, R. (2022). Converting waste plastics into construction applications: A business perspective. Environmental Impact Assessment Review, 96(January), 106814; https://doi.org/10.1016/j.eiar.2022.106814
  18. Liu, S., Kots, P.A., Vance, B.C., Danielson, A., & Vlachos, D.G. (2021). Plastic waste to fuels by hydrocracking at mild conditions. Science Advances, 7(17), 1–10; https://doi.org/10.1126/sciadv.abf8283
  19. Ma, W., Wang, C., Chen, Z., Yan, S., Cao, S., Wang, X., Chen, Y., Yang, H., & Chen, H. (2024). Catalytic hydrogenolysis of polypropylene and polyethylene mixtures: Effect of temperature on liquid alkane components. Journal of the Energy Institute, 115(January), 101615; https://doi.org/10.1016/j.joei.2024.101615
  20. Marbun, A.P., Ainin, Emawati NKD, A., Nabila, D., Samara, G. A., Sani, M. A., Negari, N., Deviani, N., Woro W, S. A., Setiawan, S., Fauhan, Z. A., & Erwandi, D. (2021). Upaya penggantian sampah plastik dalam pengemasan komoditi online shop oleh pelaku UMKM. Jurnal Pengabdian Kesehatan Masyarakat, 1(2), 145–152
  21. Marhaini, M., Fernianti, D., & Aulia, M.R. (2024). Effective pyrolysis of LDPE plastic waste to fuel using titanium dioxide catalyst. International Journal of Advanced and Applied Sciences, 11(12), 75–82; https://doi.org/10.21833/ijaas.2024.12.009
  22. Marlinda, L., Al-Muttaqii, M., Gunardi, I., Roesyadi, A., & Prajitno, D.H. (2017). Hydrocracking of Cerbera manghas oil with Co-Ni/HZSM-5 as double promoted catalyst. Bulletin of Chemical Reaction Engineering & Catalysis, 12(2), 167–184; https://doi.org/10.9767/bcrec.12.2.496.167-184
  23. Munir, D., Irfan, M.F., & Usman, M. R. (2018). Hydrocracking of virgin and waste plastics: A detailed review. Renewable and Sustainable Energy Reviews, 90(June 2016), 490–515; https://doi.org/10.1016/j.rser.2018.03.034
  24. Nugrahaningtyas, K.D., Sabiilagusti, A. I., Rahmawati, F., Heraldy, E., & Hidayat, Y. (2024). Hydrodeoxygenation of anisole via Cu supported on zeolite: HZSM-5, MOR, and Indonesian activated natural zeolite. Chemical, Food, and Environmental Engineering, 44(1). e106683 1-10; https://doi.org/10.15446/ing.investig.106683
  25. Onwudili, J.A., Insura, N., & Williams, P.T. (2009). Composition of products from the pyrolysis of polyethylene and polystyrene in a closed batch reactor: Effects of temperature and residence time. Journal of Analytical and Applied Pyrolysis, 86(2), 293–303; https://doi.org/10.1016/j.jaap.2009.07.008
  26. Qin, L., Li, J., Zhang, S., Liu, Z., Li, S., & Luo, L. (2023). Catalytic performance of Ni-Co/HZSM-5 catalysts for aromatic compound promotion in simulated bio-oil upgrading. RSC Advances, 13(11), 7694–7702; https://doi.org/10.1039/d2ra07706j
  27. Savitri, S., Nugraha, A.S., & Aziz, I. (2016). Pembuatan katalis asam (Ni/γ-Al2O3) dan katalis basa (Mg/γ-Al2O3) untuk aplikasi pembuatan biodiesel dari bahan baku minyak jelantah. Jurnal Kimia Valensi, 2(1), 1–10
  28. Sinaga, S.V., Haryanto, A., & Triyono, S. (2014). Pengaruh suhu dan waktu reaksi pada pembuatan biodiesel dari minyak jelantah [Effects of temperature and reaction time on the biodiesel production using waste cooking oil]. Jurnal Teknik Pertanian Lampung, 3(1), 27–34
  29. Smith, B. C. (2021). The infrared spectra of polymers II: Polyethylene. spectroscopy, 36(9), 24-29; https://doi.org/https://doi.org/10.56530/spectroscopy.xp7081p7
  30. Sriningsih, W., Saerodji, M. G., Trisunaryanti, W., Triyono, Armunanto, R., & Falah, I.I. (2014). Fuel production from LDPE plastic waste over natural zeolite supported Ni, Ni-Mo, Co and Co-Mo metals. Procedia Environmental Sciences, 20, 215–224; https://doi.org/10.1016/j.proenv.2014.03.028
  31. Surono, U. (2013). Berbagai metode konversi sampah plastik menjadi bahan bakar minyak. Jurnal Teknik, 3(1), 32–40
  32. Tursunov, O., Kustov, L., & Tilyabaev, Z. (2019). Catalytic activity of H-ZSM-5 and Cu-HZSM-5 zeolites of medium SiO2/Al2O3 ratio in conversion of n-hexane to aromatics, Journal of Petroleum Science and Engineering, 180, 773-778; https://doi.org/10.1016/j.petrol.2019.06.013
  33. Valizadeh, S., Jang, S.H., Rhee, G.H., Lee, J., Show, P.L., Khan, M.A., Jeon, B.H., Lin, K.Y.A., Ko, C.H., Chen, W.H., & Park, Y.K. (2022). Biohydrogen production from furniture waste via catalytic gasification in air over Ni-loaded ultra-stable Y-type zeolite. Chemical Engineering Journal, 433(P3), 133793; https://doi.org/10.1016/j.cej.2021.133793
  34. Wang, H., Yoskamtorn, T., Zheng, J., Ho, P.L., Ng, B., & Tsang, S.C.E. (2023). Ce-promoted Pt Sn-based catalyst for hydrocracking of polyolefin plastic waste into high yield of gasoline-range products. ACS Catalysis, 13(24), 15886–15898; https://doi.org/10.1021/acscatal.3c03996
  35. Wang, W., Zhang, C., Chen, G., & Zhang, R. (2019). Influence of CeO2 addition to Ni-Cu/HZSM-5 catalysts on hydrodeoxygenation of bio-oil. Applied Sciences (Switzerland), 9(6), 1257; https://doi.org/10.3390/app9061257
  36. Wardhana, P.B.W., Hanafi, A.F., Finali, A., & Umar, M.L. (2022). Potensi limbah plastik sebagai sumber energi terbarukan menggunakan proses degradasi termal dan katalitik. J-Proteksion: Jurnal Kajian Ilmiah dan Teknologi Teknik Mesin, 7(1), 14–20; https://doi.org/10.32528/jp.v7i1.8242
  37. Yu, F., Wu, Z., Wang, J., Li, Y., Chu, R., Pei, Y., & Ma, J. (2022). Effect of landfill age on the physical and chemical characteristics of waste plastics / microplastics in a waste landfill sites. Environmental Pollution, 306(February), 119366; https://doi.org/10.1016/j.envpol.2022.119366
  38. Zheng, Y., Wang, J., Li, D., Liu, C., Lu, Y., Lin, X., & Zheng, Z. (2021). Activity and selectivity of Ni–Cu bimetallic zeolites catalysts on biomass conversion for bio-aromatic and bio-phenols. Journal of the Energy Institute, 97, 58–72; https://doi.org/10.1016/j.joei.2021.04.008
  39. Zou, J., Fan, C., Jiang, Y., Liu, X., Zhou, W., Xu, H., & Huang, L. (2021). A preliminary study on assessing the brunauer-emmett-teller analysis for disordered carbonaceous materials. Microporous and Mesoporous Materials, 327(June), 111411; https://doi.org/10.1016/j.micromeso.2021.111411
  40. Zultiniar, Yelmida, A., & Shiqhi, N. (2017). Impregnasi Logam Cu Pada Hidroksiapatit dari Kulit Kerang Darah (Anadara granosa). Jurnal Sains dan Teknologi, 16(1), 20–23

Last update:

No citation recorded.

Last update: 2026-05-03 13:36:25

No citation recorded.