DOI: https://doi.org/10.61435/ijred.2026.62935
View PDF Download fulltext

Experimental analysis of a novel aerofoil-savonius type vertical axis wind turbine with an aerodynamic augmentation shell

1Department of Electrical and Electronics Engineering, College of Engineering, Australian University, Safat 13015, Kuwait

2Department of Mechanical Engineering, College of Engineering, Australian University, Safat 13015, Kuwait

3Laboratoire Polytech’Lab (POLYTECH'LAB), Université Côte d'Azur, France

4 Institut Polytechnique UniLaSalle, GeNumEr, UP 2018.C100, 14 Quai de la Somme, 80082 Amiens, France

5 Civil and Environmental Engineering Department, California State University, Fullerton, California, United States

View all affiliations
Received: 19 Jun 2026; Revised: 17 Aug 2026; Accepted: 3 Sep 2026; Available online: 10 Sep 2026; Published: 1 Nov 2026.
Editor(s): H Hadiyanto
Open Access Copyright (c) 2026 The Author(s). Published by Centre of Biomass and Renewable Energy (CBIORE)
Creative Commons License This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Citation Format:
Abstract

Savonius vertical axis wind turbines (SVAWTs) are attractive for urban and distributed energy applications because of their simple construction, omnidirectional wind acceptance, and self-starting capability, but their performance is limited by relatively low aerodynamic efficiency and high cut-in wind speeds. This study experimentally investigates a modified SVAWT that combines NACA0024 aerofoil sections at the blade extremities with an adjustable half-cylinder aerodynamic augmentation shell. The integrated configuration is evaluated as a proof-of-concept under controlled wind-tunnel conditions using both no-load and electrical-load measurements. The turbine was positioned at the exit of an open wind tunnel and tested over tunnel speeds of 9–18 m/s. The shell-assisted configuration reduced the cut-in tunnel speed from 12 to 9 m/s, increased rotational speed by up to 30%, and improved no-load voltage output by approximately 10–27%. Under resistive loading, the maximum power coefficient increased from 0.0086 to 0.0172 at 15 m/s, while peak electrical power increased by approximately 140% at 12 m/s, 100% at 15 m/s, and 68% at 18 m/s. The shell-assisted configuration also reduced the outlet-to-inlet velocity ratio and broadened the operating range over which higher torque coefficients were maintained. However, the tip-speed ratio remained below unity under all test conditions, and the absolute power coefficients were low because of the small prototype scale, low Reynolds number, absence of endplates, and rotor-generator constraints. The results demonstrate that the combined aerofoil-tip and shell configuration can provide measurable relative performance improvements compared with the same rotor operated without the shell. Further work is required to optimize the shell and aerofoil parameters, validate the flow mechanism directly, and assess performance at higher Reynolds numbers and under realistic urban wind conditions. 

Keywords: Aerodynamic augmentation; Aerofoil-Savonius wind turbine; Power coefficient enhancement; Savonius rotor; Vertical axis wind turbine.
Funding: Australian University (AU)-Kuwait under grant number IRC-2024/2025-SRC-PR011.

Article Metrics:

Article Info
Section: Original Research Article
Language : EN
Recent articles
Flexible scheduling strategy and optimization algorithm for container resources in power environment Experimental analysis of a novel aerofoil-savonius type vertical axis wind turbine with an aerodynamic augmentation shell More recent articles
Most cited articles
Characterization and Performance Test of Palm Oil Based Bio-Fuel Produced Via Ni/Zeolite-Catalyzed Cracking Process A Review on Solar PV Based Grid Connected Microinverter Control Schemes and Topologies Woodfuel in Rwanda: Impact on Energy, Poverty, Environment and Policy Instruments analysis Optimal Operation of Micro-grids Considering the Uncertainties of Demand and Renewable Energy Resources Generation Scale up sediment microbial fuel cell for powering Led lighting More cited articles
  1. Abernethy, R. B., Benedict, R. P., & Dowdell, R. B. (1985). ASME Measurement Uncertainty. Journal of Fluids Engineering, 107(2), 161–164. https://doi.org/10.1115/1.3242450
  2. Aboujaoude, H., Beaumont, F., Murer, S., Polidori, G., & Bogard, F. (2022). Aerodynamic performance enhancement of a Savonius wind turbine using an axisymmetric deflector. Journal of Wind Engineering and Industrial Aerodynamics, 220, 104882. https://doi.org/10.1016/j.jweia.2021.104882
  3. Ahmad, M., & Rehman, I. (2023). Investigating Aerodynamic Performance of Vertical Axis Wind Turbines Using Computational Techniques. Journal of Power Generation Technology, 1(1), 20. https://doi.org/10.61369/JPGT.0568
  4. Al-Gburi, K. A. H., Alnaimi, F. B. I., Al-quraishi, B. A. J., Tan, E. S., & Kareem, A. K. (2023). Enhancing Savonius Vertical Axis Wind Turbine Performance: A Comprehensive Approach with Numerical Analysis and Experimental Investigations. Energies, 16(10), 4204. https://doi.org/10.3390/en16104204
  5. Altan, B. D., & Atılgan, M. (2008). An experimental and numerical study on the improvement of the performance of Savonius wind rotor. Energy Conversion and Management, 49(12), 3425–3432. https://doi.org/10.1016/j.enconman.2008.08.021
  6. BIPM. (2023). Recent Progress in Design and Performance Analysis of Vertical-Axis Wind Turbines—A Comprehensive Review. https://www.mdpi.com/2227-9717/12/6/1094
  7. Brusca, S., Lanzafame, R., & Messina, M. (2014). Design of a vertical-axis wind turbine: How the aspect ratio affects the turbine’s performance. International Journal of Energy and Environmental Engineering, 5(4), 333–340. https://doi.org/10.1007/s40095-014-0129-x
  8. Chaiyanupong, J., & Chitsomboon, T. (2018). Effects of turbulence models and grid densities on computational accuracy of flows over a vertical axis wind turbine. International Journal of Renewable Energy Development, 7(3), 213–222. https://doi.org/10.14710/ijred.7.3.213-222
  9. Coleman, H. W. (with Internet Archive). (1999). Experimentation and uncertainty analysis for engineers. New York: Wiley. http://archive.org/details/experimentationu0000cole_2edi
  10. Coleman, H. W., Steele, W. G., & Buzhuga, M. (2010). Experimentation, Validation, and Uncertainty Analysis for Engineers. Noise Control Engineering Journal, 58(3), 343. https://doi.org/10.3397/1.3383084
  11. Deda Altan, B., & Gultekin, G. S. (2023). Investigation of Performance Enhancements of Savonius Wind Turbines through Additional Designs. Processes, 11(5), 1473. https://doi.org/10.3390/pr11051473
  12. Didane, D. H., Behery, M. R., Al-Ghriybah, M., & Manshoor, B. (2024). Recent Progress in Design and Performance Analysis of Vertical-Axis Wind Turbines—A Comprehensive Review. Processes, 12(6), 1094. https://doi.org/10.3390/pr12061094
  13. Farhat, M. H., Mehdizadeh, A., Sedaghat, A., Badawy, M. E., Djedi, B., Al-Khiami, M. I., Mostafaeipour, A., & Nazififard, M. (2025). Origami-inspired urban wind turbines: Scalable bladeless designs for decentralized renewable energy. Green Technologies and Sustainability, 4(1), 100253. https://doi.org/10.1016/j.grets.2025.100253
  14. Ghareeb, N., Sedaghat, A., Farhat, M. H., Mehdizadeh, A., Ashtian Malayer, M., El Badawy, M., & Irannezhad, M. (2026). Experimental study on flexible and rigid 3D-printed Savonius vertical axis wind turbines with aerodynamic augmentation. Wind Engineering. https://doi.org/10.1177/0309524X261443931
  15. Herath, M. T., Lee, A. K. L., & Gangadhara Prusty, B. (2015). Design of shape-adaptive wind turbine blades using Differential Stiffness Bend–Twist coupling. Ocean Engineering, 95, 157–165. https://doi.org/10.1016/j.oceaneng.2014.12.010
  16. Hughes, I., & Hase, T. (2010). Measurements and their Uncertainties: A practical guide to modern error analysis
  17. Irawan, E. N., Shibuya, K., Yamashita, K., & Fujita, G. (2024). Unlocking the power of the wind: Innovations in smart hybrid vertical axis wind turbines. International Journal of Renewable Energy Development, 13(5), 974–981. https://doi.org/10.61435/ijred.2024.60354
  18. Islam, M., Ting, D. S.-K., & Fartaj, A. (2008). Aerodynamic models for Darrieus-type straight-bladed vertical axis wind turbines. Renewable and Sustainable Energy Reviews, 12(4), 1087–1109. https://doi.org/10.1016/j.rser.2006.10.023
  19. Kacprzak, K., Liskiewicz, G., & Sobczak, K. (2013). Numerical investigation of conventional and modified Savonius wind turbines. Renewable Energy, 60, 578–585. https://doi.org/10.1016/j.renene.2013.06.009
  20. Kamoji, M. A., Kedare, S. B., & Prabhu, S. V. (2008). Experimental investigations on the effect of overlap ratio and blade edge conditions on the performance of conventional Savonius rotor. Wind Engineering, 32(2), 163–178. https://doi.org/10.1260/030952408784815826
  21. Kamoji, M. A., Kedare, S. B., & Prabhu, S. V. (2009). Performance tests on helical Savonius rotors. Renewable Energy, 34(3), 521–529. https://doi.org/10.1016/j.renene.2008.06.002
  22. Kassab, S. Z., Chemengich, S. J., & Lotfy, E. R. (2022). The effect of endplate addition on the performance of the Savonius wind turbine: A 3-D study. Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy, 236(8). https://doi.org/10.1177/09576509221098480
  23. Kumar, K. S., Jaseel, M., Brintha, R., Devi, A., Jaiswal, K. K., Sangmesh, B. M., Suresh, A., & Balaji, P. S. (2024). Performance Enhancement of a Vertical Axis Wind Turbine (NACA 25112) Using Deflector Plates as an Augmenter. In P. Tambe, P. Huang, & S. Jhavar (Eds.), Advances in Mechanical Engineering and Material Science (pp. 227–233). Springer Nature Singapore. https://doi.org/10.1007/978-981-99-5613-5_18
  24. Mohamed, M. H. (2012). Performance investigation of H-rotor Darrieus turbine with new airfoil shapes. Energy, 47(1), 522–530. https://doi.org/10.1016/j.energy.2012.08.044
  25. Mohamed, M. H., Ali, A. M., & Hafiz, A. A. (2015). CFD analysis for H-rotor Darrieus turbine as a low speed wind energy converter. Engineering Science and Technology, an International Journal, 18(1), 1–13. https://doi.org/10.1016/j.jestch.2014.08.002
  26. Mohamed, M. H., Janiga, G., Pap, E., & Thévenin, D. (2010). Optimization of Savonius turbines using an obstacle shielding the returning blade. Renewable Energy, 35(11), 2618–2626. https://doi.org/10.1016/j.renene.2010.04.007
  27. Mrigua, K., Toumi, A., Zemamou, M., Ouhmmou, B., Lahlou, Y., & Aggour, M. (2020). CFD investigation of a new elliptical-bladed multistage Savonius rotors. International Journal of Renewable Energy Development, 9(3), 383–392. https://doi.org/10.14710/ijred.2020.30286
  28. Mrigua, K., Zemamou, M., & Aggour, M. (2022). Numerical investigation of a new modified Savonius wind turbines. International Journal of Renewable Energy Development, 11(4), 1113–1123. https://doi.org/10.14710/ijred.2022.45799
  29. Ramlee, M. F., Zishan, S., Muzammil, W. K., & Fazlizan, A. (2022). Numerical investigation of solidity effect based on variable diameter on power performance of H-type Darrieus vertical axis wind turbine (VAWT). International Journal of Renewable Energy Development, 11(3), 647–660. https://doi.org/10.14710/ijred.2022.44431
  30. Rezaeiha, A., Kalkman, I., & Blocken, B. (2017). Effect of pitch angle on power performance and aerodynamics of a vertical axis wind turbine. Applied Energy, 197, 132–150. https://doi.org/10.1016/j.apenergy.2017.03.128
  31. Roy, S., & Saha, U. K. (2015). Wind tunnel experiments of a newly developed two-bladed Savonius-style wind turbine. Applied Energy, 137, 117–125. https://doi.org/10.1016/j.apenergy.2014.10.022
  32. Sedaghat, A., Djedi, B., Farhat, M. H., Al-khiami, M. I., & El Badawy, M. (2025). A novel origami inspired single rotor horizontal axis wind turbine. Journal of Energy Systems, 9(3), 271–291. https://doi.org/10.30521/jes.1723925
  33. Sedaghat, A., Farhat, M. H., Djedi, B., Al-Khiami, M. I., & El Badawy, M. (2026). Experimental investigation of a wildlife-safe origami-inspired reaction-type wind turbine for sustainable urban energy systems. International Journal of Renewable Energy Development, 15(4), 708–718. https://doi.org/10.61435/ijred.2026.62526
  34. Shahmari, M., Zarafshan, P., Kouravand, S., & Khashehchi, M. (2020). Design and Analysis of a Combined Savonius-Darrieus Wind Turbine for Irrigation Application. Journal of Renewable Energy and Environment, 7(3), 80–86. https://doi.org/10.30501/jree.2020.223382.1092
  35. Shoukat, A. A., Noon, A. A., Anwar, M., Ahmed, H. W., Khan, T. I., Koten, H., Siddiqi, M. U. R., & Sharif, A. (2021). Blades optimization for maximum power output of vertical axis wind turbine. International Journal of Renewable Energy Development, 10(3), 585–595. https://doi.org/10.14710/ijred.2021.35530
  36. Simão Ferreira, C., Van Kuik, G., Van Bussel, G., & Scarano, F. (2009). Visualization by PIV of dynamic stall on a vertical axis wind turbine. Experiments in Fluids, 46(1), 97–108. https://doi.org/10.1007/s00348-008-0543-z
  37. Tummala, A., Velamati, R. K., Sinha, D. K., Indraja, V., & Krishna, V. H. (2016). A review on small scale wind turbines. Renewable and Sustainable Energy Reviews, 56, 1351–1371. https://doi.org/10.1016/j.rser.2015.12.027
  38. Ushiyama, I., & Nagai, H. (1988). Optimum Design Configurations and Performance of Savonius Rotors. Wind Engineering, 12(1), 59–75
  39. Wong, K. H., Chong, W. T., Sukiman, N. L., Poh, S. C., Shiah, Y.-C., & Wang, C.-T. (2017). Performance enhancements on vertical axis wind turbines using flow augmentation systems: A review. Renewable and Sustainable Energy Reviews, 73, 904–921. https://doi.org/10.1016/j.rser.2017.01.160
  40. Wang, X.-H., Foo, J. S.-Y., Fazlizan, A., Chong, W.-T., & Wong, K.-H. (2024). Effects of endplate designs on the performance of Savonius vertical axis wind turbine. Energy, 310, 133205. https://doi.org/10.1016/j.energy.2024.133205
  41. Youssef, K. M., El Kholy, A. M., Hamed, A. M., Mahmoud, N. A., El Baz, A. M., & Mohamed, T. A. (2020). An innovative augmentation technique of Savonius wind turbine performance. Wind Engineering, 44(1). https://doi.org/10.1177/0309524X19849860

Last update:

No citation recorded.

Last update: 2026-09-18 01:14:34

No citation recorded.